Greenair AIR COOLED HEAT SINK

Optional accessory for ELECTRA-AIR CO2 Generators
Slides easily into unit. Use one tube for the CD-24 and two for the CD-48
Fit 125mm high temp ducting. Tube is 50cm  long

Greenair CDMC-6 CARBON DIOXIDE MONITOR CONTROLLER SYSTEM

The CDMC-6 is the most sophisticated and versatile CO2 monitor/controller available today. It uses artificial intelligence logic programming to determine the unique characteristics of your enclosure to prevent overshooting by your CO2 producing equipment and maximize on efficiency and economy.
It still remains a popular choice for those whom money is not a limiting factor. The sensor can be placed remote from the controller allowing better access to plant zone and CO2 equipment.

Greenair CT DH-3 Room Controller

While the CT-DH-3 has many applications, it was primarily developed for use with CO2 equipment and exhaust/ventilation fans. The left side (or equipment) outlets of the controller are normally "ON" until defeated when the right side outlets are activated. Internal sensors will allow for 7ºF temperature zone and a 5% humidity differential between the time that the fans come "ON" and then turn "OFF" again. When temperature or humidity rises above your dial set points, the right outlets will activate and the left outlets will deactivate. The right side outlets will remain “ON” until the temperature drops 7º and/or the humidity drops 5% below your set points. At which time, the right outlets will shut “OFF” and reactivate the left outlets.

Greenair Cyclestat 4P-1 Repeat Cycle Timer

The Cyclestat 4P repeat cycle timer optumizes accurate short cycle timing.
Many use the cycle time technique for accuratly timing the GREENAIR ELECTRA BURNER say 5-15 minute burns hourly , The Photoperiod Sensor will cut off the power to the Burner when lights off which is desirable,

Either using the GREENAIR CT-DH3-1 for tthermo and humidistat Control Of VENT FANS or Alternativly anothe rmethod is to use Another CYCLESTAT 4P-1 that is synched to VENT for a period of 5-10 mins per hour prior to the Burner firing on its cycle.
 No programming required. Easy to set and operate.
 Microprocessor time counter with adjustable frequency and duration.
The Cyclestat 4P timer has many uses. Only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake or exhaust fan control. The Cyclestat may be set for interval and cycle of timed events. Interval is the time between the "On" and "Off" cycles. The interval knob may be set from 5 minutes to 8 hours. Set this for desired time between functions. Cycle is the length of time that a specific function or condition must be maintained. Cycle may be set from 5 seconds to 30 minutes.

Greenair MCC-1 Multi function Room Controller

The Micro Climate Controller MCC-1 is designed to perform all the major atmospheric and timed functions required in an automated growth environment including temperature, humidity, carbon dioxide enrichment, lighting and irrigation control. The controller incorporates an external coil cooling thermostat , a dehumidifying humidistat, a 24-hour clock timer, a photo-sensor and a repeat cycle timer. Heating and humidifying control is provided by triggers for remote high-amperage relays which enable synchronized equipment management. Automatic override and defeat systems coordinate controls to consider all possible variables. The MCC-1 is enclosed in a black anodized, brush finish aluminum housing. An attractive screen-printed front panel with function indicator lights makes system monitoring and adjustment quick and easy. All connections are standard 3-prong grounded plugs and receptacles. No hard wiring is required for basic operations. Low and high voltage relays are available to operate auxiliary equipment. Every aspect of the growing environment may be addressed by the Micro Climate Controller (MCC-1). Operates on 240v with 15 Amp switching capacity.

Greenair SPC-1  CO2 SET POINT CONTROLLER

Our SPC-1 Set Point Controller has become the most popular choice of CO2 controller. This is because of its ease of installation and operation. It functions much like a simple thermostat, except it is for CO2 enrichment. It is affordably priced and meets all the requirements of a typical plant growth environment.
Click on the image at the bottom of the page for more details.